codet01 codet02 codet03 codet04 codet05 codet06 codet07 codet08 codet09 codet10 codet11 codet12

  • SLOT GACOR
  • slot gacor
  • slot gacor
  • SLOT GACOR
  • SLOT GACOR
  • SLOT GACOR
  • SLOT GACOR
  • SLOT GACOR
  • hanomantoto
  • hanomantoto
  • SLOT GACOR
  • SLOT GACOR
  • Slot gacor
  • SLOT GACOR
  • Slot pulsa
  • Slot gacor
  • PBN
  • PBN
  • slot gacor
  • slot gacor 4d
  • slot gacor 4d
  • slot gacor 4d
  • slot gacor 4d
  • slot gacor
  • slot gacor
  • togel jackpot
  • SLOT GACOR
  • slot gacor
  • SLOT GACOR
  • SLOT GACOR
  • SLOT GACOR
  • SLOT GACOR
  • SLOT DEMO PRAGMATIC
  • SLOT PULSA
  • SLOT GACOR
  • SLOT GACOR
  • SLOT GACOR
  • SLOT GACOR
  • SLOT GACOR
  • SLOT GACOR
  • SLOT GACOR
  • SLOT GACOR
  • SLOT GACOR
  • SLOT GACOR
  • SLOT GACOR
  • SLOT demo
  • BOKEP INDO

  • Warning: session_start(): Cannot send session cookie - headers already sent by (output started at /home/ohmdenki/public_html/index.php:6) in /home/ohmdenki/public_html/app/autoload.php on line 2

    Warning: session_start(): open(/var/cpanel/php/sessions/ea-php72/sess_kg2jcdp69h81h5rirtk9v7l482, O_RDWR) failed: Disk quota exceeded (122) in /home/ohmdenki/public_html/app/autoload.php on line 2

    Warning: session_start(): Cannot send session cache limiter - headers already sent (output started at /home/ohmdenki/public_html/index.php:6) in /home/ohmdenki/public_html/app/autoload.php on line 2
    Model Selection

    Model Selection

    Model Selection

    Precautions in selecting a model

    * Actual cooling capacity can be affected by airtightness of an enclosure, placement of heat generators and dirt on the capacitors, evaporators or filters. It is recommended to select a larger model than minimum requirements.
    * Do not set the internal temperature at unnecessarily low level.
    * When the enclosure is located near a furnace or any place exposed to heat radiation, select a larger model than the calculation.

    Values required for model selection

    For evaluating a cooling capacity of an enclosure cooler,the following values are required.

    機種選定に必要な制御盤の使用条件

     

    If desired setting temperature is lower than the max. ambient temperature

    最高外気温度より盤内希望設定温度が低い場合

     

    If desired setting temperature is higher than the max. ambient temperature

    最高外気温度より盤内希望設定温度が高い場合

     

    * Heat intrusion rate U for an iron-made enclosure is generally 5 to 6〔W/(m2・K)〕. In this example,U=5〔W/(m2・K)〕is used.
    * This information has been adapted from “Technical data No. 005-2005 Cooling performance evaluation test method for refrigeration cycle cabinet coolers”by Thermal Solution Equipment for Cabinet Technical Association,Japan.


    Warning: Unknown: open(/var/cpanel/php/sessions/ea-php72/sess_kg2jcdp69h81h5rirtk9v7l482, O_RDWR) failed: Disk quota exceeded (122) in Unknown on line 0

    Warning: Unknown: Failed to write session data (files). Please verify that the current setting of session.save_path is correct (/var/cpanel/php/sessions/ea-php72) in Unknown on line 0